Pipeline Elbow/Pipeline Bend


Piping Elbows and Bends are very important pipe fitting which are used very frequently for changing direction in piping system. Piping Elbow and Piping bend are not the same, even though sometimes these two terms are interchangeably used.

A bend is simply a generic term in piping for an “offset” – a change in direction of the piping. It signifies that there is a “bend” i.e,  a change in direction of the piping (usually for some specific reason) – but it lacks specific, engineering definition as to direction and degree. Bends are usually made by using a bending machine (hot bending and cold bending) on site and suited for a specific need. Use of bends are economic as it reduces number of expensive fittings. 


Bend

Source: https://riomardhian.files.wordpress.com/2015/02/86.jpg?w=676

An elbow, on the other hand, is a specific, standard, engineered bend pre-fabricated as a spool piece  (based on ASME B 16.9) and designed to either be screwed, flanged, or welded to the piping it is associated with. An elbow can be 45 degree or 90 degree. There can also be custom-designed elbows, although most are catagorized as either “short radius” or long radius”.

Elbow
Source: https://blogger.googleusercontent.com/img/b/R29vZ2xl/AVvXsEiNmFNMIC2PFcTYIoha8gv7ZLzm5iarytW0_AJ_tlcOBbkrywgus3pT-E06H0lNJ2IZMG4iDZFOvJ1SFsAJ1jSx2dXCqoPuqU1SJ7kA2Gtftk1OGLJXVSOKpu6nyNqk-oz5qQU1FiBVXMWp/s1600/Untitled1.png
Elbows can change direction to any angle as per requirement. An elbow angle can be defined as the angle by which the flow direction deviates from its original flowing direction. Even though An elbow angle can be anything greater than 0 but less or equal to 90°But still a change in direction greater than 90° at a single point is not desirable. Normally, a 45° and a 90° elbow combinedly used while making piping layouts for such situations.

There is always a doubt about the terms bends and elbows. They are frequently used as synonyms.  The difference between them is as follows:
  1. Bend is a generic term for any offset or change of direction in the piping. It is a vague term that also includes elbows.
  2. An elbow is an engineering term and they are classified as 90 deg or 45 deg, short or long radius.
  3. Elbows have industrial standards and have limitations to size, bend radius and angle. The angles are usually 45 deg or 90 degrees. All others offsets are classified as pipe bends.
  4. Bends are generally made or fabricated as per the need of the piping; however elbows are pre fabricated and standard, and are available off the shelf.
  5. Bends are never sharp corners but elbows are. Pipe bending techniques have constraint as to how much material thinning can be allowed to safely contain the pressure of the fluid to be contained.  As elbows are pre fabricated, cast or butt welded, they can be sharp like right angles and return elbows which are 180 degrees.
  6. Elbow is a standard fitting but bends are custom fabricated.
  7. In bends as the pipe is bent and there is no welding involved, there is less pipe friction and flow is smoother. In elbows, the welding can create some friction.
  8. All elbows are bends but all bends are not elbows.
  9. Bend has a larger radius then elbows.
  10. Generally the most basic difference is the radius of curvature. Elbows generally have radius of curvature between one to twice the diameter of the pipe.  Bends have a radius of curvature more than twice the diameter.
Elbows or bends are available in various radii for a smooth change in direction which are expressed in terms of pipe nominal size expressed in inches. Elbows or bends are available in three radii,
  1. Long radius elbows (Radius = 1.5D): used most frequently where there is a need to keep the frictional fluid pressure loss down to a minimum, there is ample space and volume to allow for a wider turn and generate less pressure drop.
  2. Long radius elbows (Radius > 1.5D): Used sometimes for specific applications for transporting high viscous fluids likes slurry, low polymer etc. For radius more than 1.5D pipe bends are usually used and these can be made to any radius.However, 3D & 5D pipe bends are most commonly used.
  3. Short radius elbows (Radius = 1.0D): to be used only in locations where space does not permit use of long radies elbow and there is a need to reduce the cost of elbows. In jacketed piping the short radius elbow is used for the core pipe.


Source:
http://www.whatispiping.com/piping-elbows-and-bends
http://www.marineinsight.com/tech/pipeing/pipes-and-bends-an-essential-guide-for-second-engineers-part-2/



14 comments:

  1. Nice blog on Pipe Bending Machine . I will share this to my friends.

    ReplyDelete
  2. Thanks for sharing the post. Pipe fittings are very important is used very frequently for changing in piping system.The best Steel Suppliers in chennai will support us to grow. The quality is the main thing to construct a building. Then also the quality of Steel Dealers in Chennai will satisfy the customer needs.

    ReplyDelete
  3. Thanks for great suggestion about PIPELINE BEND and If anyone want to get ideas of Stainless Steel Pipe Fittings than visit my website Stainless Steel Pipe Fittings

    ReplyDelete
  4. Thanks for sharing such a nice blog. If you need any pipe fittings making machine then visit Three Plast Machinery.

    ReplyDelete
  5. Great Post. Thanks for sharing with us. For pipe fittings Visit my website: pipe fittings making machine

    ReplyDelete
  6. Nice blog, by the way. Thanks for sharing this information. In the long term, I would like to see more blogs. You can also visit: Ball Valves Manufacturer

    ReplyDelete
  7. Thanks for providing the best UPVC Elbows manufacturing in India. More details- https://websitepetron2016.wixsite.com/website, know about the best manufacturer company based in India- Petron Thermoplast.

    ReplyDelete
  8. https://www.united-steel.com/
    United Steel Industry CO., LTD is a professional manufacturer & exporter of steel pipes in China. Products include carbon steel pipe(SMLS pipe/ ERW/ LSAW/ SSAW), stainless steel pipe, galvanized steel pipe, alloy steel pipe and the related products.
    Welcome every inquiry!

    ReplyDelete
  9. Keep sharing such informative posts. Best valves and strainers supplier offers Pipe Fittings. We offer high quality Pipe Fittings at low cost.
    Check Valve manufacturers

    ReplyDelete
  10. pure ghee in dubai is hard to find did you have any idea about this

    ReplyDelete
  11. great man great knowledge you have since you have knowledge i want to ask do you have any idea how pipeline will work with Abkantpresse gebraucht

    ReplyDelete
  12. What an insightful breakdown of piping elbows and bends! Your explanation effectively distinguishes between the two, highlighting their engineering specifications and practical uses. For those in need of quality fittings, Direct Wholesale offers a variety of cabling conduit fittings, including bends. This post serves as a valuable resource for anyone involved in piping system design and installation. Check out Direct Wholesale's selection here: https://directwholesale.com.au/conduit/cabling-conduit-fittings/cabling-conduit-fittings-bends

    ReplyDelete